- 8 x 10/100Base-T(X) copper ports, all with PoE+
- Plug and play: no configuration, the switch is ready when powered, with no software and no settings
- Auto negotiation and auto MDI/MDIX on every copper port: straight or crossed cables both work
- Store-and-forward switching with IEEE 802.3x flow control in full duplex and back pressure in half duplex
- MAC address table of 1K entries
- PoE+: IEEE 802.3af and 802.3at on all 8 ports, up to 30 W per port
- Built-in 90 W supply shared by all ports; above about 50 deg C the total PoE power is reduced
- Each port is checked before power is applied and switched off on overload or short circuit; port fuses and surge diodes, input fuse and varistor
- Link and activity LED for every copper port
- 100 - 240 V AC (120 - 370 V DC), 50 - 60 Hz power input, isolation of the power supply 4 kV AC
- Operating temperature -30 to +80 deg C
- Rugged metal housing, IP 40, 44 x 95 x 125 mm
- DIN rail mounting
SWITCHING - BSB
Switching
Store-and-forward switching with IEEE 802.3x flow control in full duplex and back pressure in half duplex
Auto Negotiation and MDI/MDIX
auto negotiation and auto MDI/MDIX on every copper port: straight or crossed cables both work
MAC Address Table
1K entries
Standards
IEEE 802.3, 802.3u, 802.3x, 802.3af, 802.3at
Configuration
no software and no web page to configure; the switch is ready when powered
POE+ - BSB
Standards
IEEE 802.3af and 802.3at on all 8 ports
Power per Port
up to 30 W per port
PoE Supply
built-in 90 W supply shared by all ports; above about 50 deg C the total PoE power is reduced
Port Check
each port is checked before power is applied and switched off on overload or short circuit
Port Protection
each PoE+ port has its own 1 A fuse; port fuses and surge diodes
CONNECTORS AND PORTS - BSB
10/100T(X) RJ45 Ports
8 x RJ-45, 10/100 Mbit/s, ETH1 to ETH8, with auto MDI/MDIX
Cable
10BASE-T: Cat. 3, 4 or 5, 100-ohm UTP; 100BASE-TX: Cat. 5, 100-ohm UTP; maximum length 100 m (328 ft)
RJ-45 Pins
pins 1, 2, 3 and 6 carry the data of 10BASE-T and 100BASE-TX; pins 4, 5, 7 and 8 are not used for data
PoE+ Pins
pins 1, 2 and 3, 6 carry Ethernet data and PoE+ power; pins 4, 5 and 7, 8 are not used (no data and no power)
Power Terminal
3-pin terminal block, 7.62 mm pitch; pin 1: protective earth (PE), connected to the case; pins 2 and 3: AC supply input (line conductor and neutral conductor)
Protective Earth
connect the protective earth conductor first
Warning
mains voltage; installation by qualified personnel only; disconnect power before wiring
LED INDICATORS - BSB
Port LEDs
one link / activity LED for each port ETH1 to ETH8, in two rows of four; each LED shows the link and activity of its port
POWER - BSB
Input Range
100 - 240 V AC (120 - 370 V DC), 50 - 60 Hz; the built-in 90 W supply feeds the PoE+ ports
Isolation
4 kV AC (power supply)
Protection
input fuse and varistor, port fuses and surge diodes, PoE overload cut-off
PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS - BSB
Enclosure
Metal, IP 40
Dimensions
44 x 95 x 125 mm (w x d x h)
Weight
approx. 400 g
Operating Temperature
-30 to +80 deg C
Storage Temperature
-40 to +85 deg C
Operating Humidity
5 - 95 %, non-condensing
Mounting
DIN rail
BSB268: Industrial unmanaged Ethernet switch, 8 PoE+ ports, 90 W, AC power input