- 8 x 10/100Base-T(X) copper ports and 2 x SFP slots
- Plug and play: no configuration, the switch is ready when powered, with no software and no settings
- Auto negotiation and auto MDI/MDIX on every copper port: straight or crossed cables both work
- Store-and-forward switching with IEEE 802.3x flow control in full duplex and back pressure in half duplex
- MAC address table of 16K entries
- Fiber uplinks: two SFP slots for 1000BASE-X or 100BASE-FX modules (100 Mbit/s or 1 Gbit/s); a plugged-in fiber module takes over the uplink port
- ACT and SPD LEDs for each SFP slot
- Link and activity LED for every copper port
- 9 - 48 V DC power input, polarity-independent: the supply can be connected either way round
- Operating temperature 0 to +70 deg C
- Rugged metal housing, IP 40, 44 x 95 x 125 mm
- DIN rail mounting
SWITCHING - BSB
Switching
Store-and-forward switching with IEEE 802.3x flow control in full duplex and back pressure in half duplex
Auto Negotiation and MDI/MDIX
auto negotiation and auto MDI/MDIX on every copper port: straight or crossed cables both work
MAC Address Table
16K entries
Standards
IEEE 802.3, 802.3u, 802.3x, 802.3z
Configuration
no software and no web page to configure; the switch is ready when powered
SFP PORTS - BSB
SFP Slots
two slots for 1000BASE-X or 100BASE-FX modules (100 Mbit/s or 1 Gbit/s)
Uplink
a plugged-in fiber module takes over the uplink port
SFP LEDs
ACT and SPD LEDs for each SFP slot
Tested Modules
the modules checked in laboratory tests in 2020 and 2021 are listed in chapter 7 of the user manual; a module that is not listed may work, but it was not checked
CONNECTORS AND PORTS - BSB
10/100T(X) RJ45 Ports
8 x RJ-45, 10/100 Mbit/s, ETH1 to ETH8, with auto MDI/MDIX
Cable
10BASE-T: Cat. 3, 4 or 5, 100-ohm UTP; 100BASE-TX: Cat. 5, 100-ohm UTP; maximum length 100 m (328 ft)
RJ-45 Pins
pins 1, 2, 3 and 6 carry the data of 10BASE-T and 100BASE-TX; pins 4, 5, 7 and 8 are not used for data
SFP Slots
SFP1 and SFP2, for 1000BASE-X or 100BASE-FX modules
Power Terminal
2-pin terminal block, 3.81 mm pitch; pins 1 and 2: DC supply, either polarity (DC +/-)
LED INDICATORS - BSB
Port LEDs
one link / activity LED for each port ETH1 to ETH8, in two rows of four; each LED shows the link and activity of its port
SFP LEDs
ACT and SPD LEDs of the SFP slots, two LEDs for each of SFP1 and SFP2
POWER - BSB
Input Range
9 - 48 V DC
Polarity
polarity-independent input: the supply can be connected either way round
PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS - BSB
Enclosure
Metal, IP 40
Dimensions
44 x 95 x 125 mm (w x d x h)
Weight
approx. 380 g
Operating Temperature
0 to +70 deg C
Storage Temperature
-40 to +85 deg C
Operating Humidity
5 - 95 %, non-condensing
Mounting
DIN rail
BSB120: Industrial unmanaged Ethernet switch, 8 ports and 2 SFP uplinks, 9 - 48 V DC power input