- Supports 4 x 10/100Base-T(X) ports + 1 x BPL link
- Supports Full/Half-Duplex, auto MDI/MDI-X on each port
- Wide operating temperature range from -40 to 85 °C
- Rugged Metal IP-40 housing design
- DIN-Rail mounting
- Supports up to 30Mbps PHY rate on BPL with Up to 10 hops and 1000 nodes
- Up to 432 sub-carriers from 2 to 28MHz analog bandwidth
- Support LDPC-C FEC with 128-bit AES core
- Plug and play with Master/Slave selection via switch
TECHNOLOGY
BPL (BROADBAND POWERLINE) TECHNOLOGY
PHY Data Rate
Up to 240 MHz
MAC Layer Protocol
CSMA/CA
Modulation Technology
OFDM-432
VLAN
IEEE802.1q/ IEEE802.1p/ IEEE802.3d
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-T(X)
IEEE 802.3x Flow Control
Mac Table
1K MAC address entry
Processing
Store-and-Forward
Memory
448K bits packet buffer memory
Auto Power Saving Mode
Automatically enters this mode if no cable link is established.
INTERFACE AND INDICATORS
Power Indicator
Power LED
10/100TX RJ45
Activity LEDs
LEDs
-BPL Activity
-BPL Link
-Master Indication (LED ON: Master, LED OFF: Slave)
Master/Slave Switch for BPL
Selection for BPL whether to operate as Master or Slave
POWER AND DATA INPUTS
Power and Data Input Options
PN Model: Phase to neutral model (Standart Model). That version gets power from terminal pins 1 and 2 from phase and neutral. It can also transmit data from that pins 1 and 2 and other pins usage is optional (Ex: Master can be connected to all phases and slaves can be connected to relevant phases)
PP Model: Phase to phase model. That version also gets power from terminal pins 1 and 2 from phase and neutral. Data transmission only done through terminal pins 3 and 4. AC Phase to phase connection can be done to data transmission pins for better performance.
If phase to phase connection is not used then phase and neutral can still be connected for data transmission for terminal pins 3 and 4 for PP Model.
Power Input Range Options
Powering up device is only done over Terminal pins 1 and 2.
AC Model: Device can be powered up with AC input, this option is available in both PN and PP models. It accepts, 110V–240V/50-60Hz. Power Input can also be used for data transmission.
DC Model: Device can be powered up with 9-36V DC power. Data transmission only done through terminal pins 3 and 4. This model can be used if DC power source will be used in the field and only available with PP model.
PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
Enclosure
Metal, IP 40
Dimensions
43 x 95 x 124 (w x d x h) mm
Weight
382gr
Storage Temperature
-65 to 150 °C
Operating Temperature
-40 to 85 °C
Operating Humidity
5% to 95%Non-condensing
APPLIED STANDARDS
EMI
FCC Part 15, CISPR (EN55022) class A
EMS
EN61000-4-2 (ESD),
EN61000-4-3 (RS),
EN61000-4-4 (EFT),
EN61000-4-5 (Surge),
EN61000-4-6 (CS),
EN61000-4-8, EN61000-4-11
Shock
IEC60068-2-27
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6
Safety
EN60950
Warranty
3 years
BSB615 - PP - DC: Industrial Unmanaged Ethernet Switch, 4 x 10/100 T(x) ETH ports + 1 x BPL (Broadband Power Line) Link, 9-36V DC Power Input, Phase to Neutral and Phase to Phase Connection on Data Terminals
