REDZ Smart Communication Technologies

- Supports 2 x 10/100Base-T(X) ports + 1 x BPL link
- Wide Range 3 phase input, 110V–240V/50-60Hz wide range power input
- Supports up to 30Mbps PHY rate on BPL with Up to 10 hops and 1000 nodes
- Up to 432 sub-carriers from 2 to 28MHz analog bandwidth on BPL
- Support LDPC-C FEC with 128-bit AES core on BPL
-   Supports Full/Half-Duplex, auto MDI/MDI-X on each port
-   DHCP Server Capability
-   Supports 1 x RS232 and 1 x RS485 Serial Connection up to 460800 Baud
-   Embedded web interface for ease of use
-   Up to 10 client connection in Server Mode
-   2 different Gateway Operating Modes:
Transparent Communication - TCP to TCP, TCP to Serial, Serial to Serial
Modbus TCP to RTU Conversion
-   Creates Radio Network:
Point to point
Point to multi point - Broadcast
Point to multi point - TCP Socket to target address mapping based data transfer
-   2.4GHz LoRa based Radio Frequency (RF) Communication
-   128 bit AES Encryption and Decryption on over the air communication
-   2.4GHz Version:
LoRa Signal Bandwidth Configurable: 200, 400, 800, 1600 kHz
LoRa Radio Power Configurable between -18dBm (~0,02mW) to 13dBm (~20mW)
LoRa or FLRC Selectable Modulation Options
-   LoRa Rx Group Address and Device Address Configurable
-   LoRa Tx Group Address and Device Address Configurable
-   Easy to follow LoRa data packages on web interface
-   Easy to follow Device Status on web interface
-   Black List and White List based LoRa package filter
-   Firmware Upgrade over Web
-   2 firmware storage capability on same device (1 active only)
- Wide operating temperature range from -40 to 85 °C
- Rugged Metal IP-40 housing design
- DIN-Rail mounting

TECHNOLOGY

LoRa TECHNOLOGY
Based on
Powerful Cortex M3
Pre-Certified according to EN 300 328
Sensitivity
Down to -130 dBm
Output Power level
Up to 13dBm
Link Budget
Up to 142 dB
Communication Distance
More than 12km (Line of Sight)
Typical Communication Distance Indoor/Urban
>2km
Frequency Range
Min 2 402 000 137 Hz
Max 2 479 999 939 Hz
LoRa Bandwidth Options
200 kHz
400 kHz
800 kHz
1600 kHz
Tx Power Level
-18dBm (~0,02mW) to 13dBm (~20mW)
Configurable
LoRa Spreading Factor
SF5
SF6
SF7
SF8
SF9
SF10
SF11
SF12

ETHERNET SWITCH TECHNOLOGY
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-T(X)
IEEE 802.3x Flow Control
Mac Table
1K MAC address entry
Processing
Store-and-Forward
Memory
448K bits packet buffer memory

BPL (BROADBAND POWERLINE) TECHNOLOGY
PHY Data Rate
Up to 240 MHz
MAC Layer Protocol
CSMA/CA
Modulation Technology
OFDM-432
VLAN
IEEE802.1q/ IEEE802.1p/ IEEE802.3d

CONNECTORS AND PORTS

SMA Antenna Connector for LoRa
1 Standard SMA male interface, 50 ohm
Console Port
Micro USB or USB Type-C connection for LOG in 115200 baud
10/100T(X) RJ45 Ports
Ethernet Connection on 2 ports
Serial Ports
5 pin wired Terminal Connection
Tx, Rx, GND for RS232
A and B for RS485
Reset Buttons
Reset to Client and Reset to Server Operating modes buttons

LED INDICATORS

Power indicator
Power LED

10/100T(X) Indicators
Activity LEDs:
ETH1, ETH2 and TLM (Activity of device itself)
System Indicators

Status LED,
Tx and Rx of data LEDs and Server LED
(LED ON: Server Operating Mode, LED OFF: Client Operating Mode)

LoRa Indicators

Alive (Blinks during normal operation), Tx and Rx of data LEDs

Console Indicators

Tx and Rx of data LEDs

BPL LEDs

-BPL Activity

-BPL Link

-Master Indication ( LED ON: Master, LED OFF: Slave)

POWER

Input Range
3 phase input, 110V–240V/50-60Hz
Power and Data
AC Power supply use L1-N only. Phase 2-3 connections are used to BPL signal transmission.

PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS

Enclosure
Metal, IP 40
Dimensions
43 x 95 x 124 (w x d x h) mm
Weight
~400gr
Storage Temperature
-65 to 150 °C
Operating Temperature
-40 to 85 °C
Operating Humidity
5% to 95% Non-condensing

TLM695: 2.4GHz LoRa RF Modem, 2x 10/100 T(x) ETH ports + 1 x BPL (Broadband Power Line) Link, 1 x RS232 & 1 x RS485, 3 Phase AC Power Input, 110V–240V/50-60Hz

TCP/IP Discovery Tool

↗ User Manual ☶ Datasheet